Full adhesive glue: Designed with adhesive to the entire screen protector, not just on edges, makes it perfectly fit on the screen without peeling off.
Response Sensitivity: Accurate size and strong adhesive UV glue to ensure the film perfectly fit.
9H Hardness Surface: Anti-scratch 0.33 mm ultra thin Rounded Edge design with High-Definition Clarity.
Case friendly : compatible with phone cases. While it covers the phone screen, it leaves some space on each side to ensure perfect fit with your case.
How to install this Screen protector>>
1. Use a foil cleaning kit to wipe the phone to be clean.
2 .Place the sticker over the hole in the handset. Stick the key hole with a label.
3 .Place custom glue drops on flat, clean and dust-free glass screens. Use each glue to use. It is recommended that the glue be poured completely. The excess glue can be wiped clean before turning on the lights. The glue can only be a mass and cannot be separated. Drops on the screen.
4 .The glue that drops on the screen can\`t have air bubbles, if there is air bubble, use the needle to pierce the air bubble to let go air.
5 .Remove the release film from the protective film and place the glass on the screen so that the glass contacts the glue and gently translate the glass to a suitable position. Do not lift the glass and allow the glass to separate from the glue (very important).
6 .Wait for about 30 seconds to let the glue slowly spread and level.
7. There is glue overflow, wipe off with a clean cloth. After checking the retention criteria for the mobile phone\`s tempered film, the lamp was turned back and forth three times around the edge of the phone, and after 3 seconds of initial curing (not in the middle), the edge glue was wiped again until the glue overflowed. (Prevent white edges or long bubbles on edges)
8. Wait for the exhaust to complete, after the glue overflows cleanly, after the positioning standard of the tempered film is satisfied, turn on the light. Otherwise scrapped material.
9. Irradiate the mobile phone under UV light and need to illuminate twice for about 3 minutes to reach the fully-cured position.
Please Don't press or touch the screen after you drop the glue(very important),Glue will automatically spread the entire screen
after install the protector please use the lamp to dry the glass about 3 minutes (screen and edges), it is very important
this glass is case friendly style,can't cover the whole screen(There is about 2mm gaps at the edges), please pay attention to it
the glass can be removed , but you must make sure to use the lamp to dry the glass enough about 3 minutes when you install the protector, otherwise the glass is not easy to remove!!
Response Sensitivity: Accurate size and strong adhesive UV glue to ensure the film perfectly fit.
9H Hardness Surface: Anti-scratch 0.33 mm ultra thin Rounded Edge design with High-Definition Clarity.
Case friendly : compatible with phone cases. While it covers the phone screen, it leaves some space on each side to ensure perfect fit with your case.
How to install this Screen protector>>
1. Use a foil cleaning kit to wipe the phone to be clean.
2 .Place the sticker over the hole in the handset. Stick the key hole with a label.
3 .Place custom glue drops on flat, clean and dust-free glass screens. Use each glue to use. It is recommended that the glue be poured completely. The excess glue can be wiped clean before turning on the lights. The glue can only be a mass and cannot be separated. Drops on the screen.
4 .The glue that drops on the screen can\`t have air bubbles, if there is air bubble, use the needle to pierce the air bubble to let go air.
5 .Remove the release film from the protective film and place the glass on the screen so that the glass contacts the glue and gently translate the glass to a suitable position. Do not lift the glass and allow the glass to separate from the glue (very important).
6 .Wait for about 30 seconds to let the glue slowly spread and level.
7. There is glue overflow, wipe off with a clean cloth. After checking the retention criteria for the mobile phone\`s tempered film, the lamp was turned back and forth three times around the edge of the phone, and after 3 seconds of initial curing (not in the middle), the edge glue was wiped again until the glue overflowed. (Prevent white edges or long bubbles on edges)
8. Wait for the exhaust to complete, after the glue overflows cleanly, after the positioning standard of the tempered film is satisfied, turn on the light. Otherwise scrapped material.
9. Irradiate the mobile phone under UV light and need to illuminate twice for about 3 minutes to reach the fully-cured position.
Please Don't press or touch the screen after you drop the glue(very important),Glue will automatically spread the entire screen
after install the protector please use the lamp to dry the glass about 3 minutes (screen and edges), it is very important
this glass is case friendly style,can't cover the whole screen(There is about 2mm gaps at the edges), please pay attention to it
the glass can be removed , but you must make sure to use the lamp to dry the glass enough about 3 minutes when you install the protector, otherwise the glass is not easy to remove!!
×
×